Select your language

From time to time, I run some benchmarks on various machines for MAME, to be able to give some advice on minimum hardware requirements.

To run MAME, and in particular the TI emulations, your host (PC, Laptop) must offer a minimum performance. You might wonder why a PC with gigahertz CPU may run into trouble when emulating an 80ies computer with 3 Megahertz clock, but the point is that MAME emulates the electrical circuits at a fairly precise level, and while in your real system, lots of things may happen in parallel, this is not the case in emulation.

Here are some tests that show you what you can expect. The percentages show how well the emulator managed to keep pace with the real system; they indicate the number of emulated seconds in relation to the real time seconds. Only when you have a 100% result, the emulation runs at the precise speed; otherwise the running time is stretched. One may also say that the numbers say how much work it has managed to do when the real system did 100%.

PC platform

The following table comprises PC platforms like laptops or desktops. As shown, the TI-99 emulations in MAME run satisfactorily on platforms after 2010.

Raw bench performance

In this table, performance data has been recorded from bare benchmark runs without graphic output. In that case, the emulation is run without time synchronization, at maximum speed. If you get a 200% value this means that the emulation runs at twice the speed as the real system.

It is not sufficient to get a 100% benchmark value in this test. This is because the graphic output means a considerable load for the emulation; see the table in the next section. Hence, these values are independent of the graphic performance of your system.

  MAME release Speed GHz TI-99/4A TI-99/4A + EVPC SGCPU aka TI-99/4P Geneve TI-99/8 + HX5102 TI-99/2 + HX5102
 PC Core i7-6700 0.218 4.0 731%
706% 827%  483% 243% 568%

 

Emulated disk operations also cause a high performance impact. For example, if we let the Geneve boot during the test, the performance drops from 483% to 416%.

Graphic performance

In this table, performance data has been recorded from test runs with graphic output. This is most interesting to see whether you can expect a good emulation experience without lagging, chopped sounds, or unrealistic slow execution. However, the value definitely depends on the performance of your graphic card (2D performance). It may be better or worse for your specific card.

  MAME release Speed GHz TI-99/4A TI-99/4A + EVPC SGCPU aka TI-99/4P Geneve TI-99/8 + HX5102 TI-99/2 + HX5102
Atom N270 0.230 1.6 14% 16% n.t. 13% n.t. n.t.
Laptop Celeron 0.208 2.0 19% 14% 15% 14% 10% 16%
Thinkpad T60 Core2 Duo 0.208 1.8 92% 89% 91% 85% 45% 91%
Laptop Core i5-3320M 0.208 2.6 100% 100% 100% 100% 100% 100%
 PC Core i7-6700K 0.208 4.0 100% 100% 100% 100% 100% 100%
PC Core i7-7700 0.208 3.6 100% 100% 100% 100% 100% 100%

 

Small devices

I also ran some tests on Raspberry Pi. Before Pi 4, the Raspberry was plainly unusable for the TI-99 emulation in MAME. You may have probably heard about MAME emulations running decently on the Raspberry, but the performance of MAME largely depends on the emulated system. The TI-99 family is emulated in high precision, which requires a lot of performance.

Raw bench performance

As above, the plain emulation performance without graphic output is considered. These values are independent of the graphic performance of the device.

  MAME release Speed GHz TI-99/4A TI-99/4A + EVPC SGCPU aka TI-99/4P Geneve TI-99/8 + HX5102 TI-99/2 + HX5102
Raspb. Pi 4 0.223 1.5  141%  131% 154% 74% 45%  85%

Graphic performance

This table shows the performance with graphic output.

  MAME release Speed GHz TI-99/4A TI-99/4A + EVPC SGCPU aka TI-99/4P Geneve TI-99/8 + HX5102 TI-99/2 + HX5102
Ras.Pi 3 B+ 0.208 1.4 6% 4% 4% 4% 4% 5%
Raspb. Pi 4 0.223 1.5 100% 97% 99% 64% 44% 79%

 

I believe that the Raspberry Pi3 B+ was not running by optimum conditions, and there may be some tricks to get a better performance.

To my surprise, the Raspberry Pi 4 managed to run the TI-99/4A emulation in full speed. This mean a tremendous increase in performance and makes it possible to run the MAME emulation on that device for the first time.

The graphic output has a much smaller footprint on the Pi 4 than expected. It seems as if the graphic performance is not a bottleneck for the Raspberry anymore.

Note however, as mentioned above, that the performance highly depends on further emulation operations with high impact, like disk operations. This means that if you do a lot of disk operations, the TI-99/4A performance on the Raspberry Pi 4 drops from 100% to 92%. This may still be sufficient for a good emulation experience, though.

Even if a Raspberry seemingly performs well for all your typical PC applications, the MAME emulation is a big challenge for it. You should keep in mind that a typical high-end PC pulls about 200 W electrical power, while a Raspberry does not exceed 15 W. The higher power consumption comes from the high performance of CPU and graphics card. Hence, some basic physical considerations tell us that a Raspberry will not reach the performance of a fully equipped desktop PC.

We use cookies on our website. All of these cookies are essential for the operation of the site. They are only used on this site and not transmitted to any third party. None of them are Tracking Cookies, and they do not serve to analyze your behavior.